How to fish a wire down a wall

At the speakers, poke the wiring into the wall. Exit the drywall down at baseboard height. Do your horizontal work. Reattach baseboard trim.

Go up into the attic and take a long sharp device and tap a small pin hole in the ceiling of the room below and leave the tool in the hole right next to where you let the speaker wire down into the wall. Then you will know where the wire is. Drop a weight on the end of a piece of string down through the higher hole, then fish with a long piece of timber or fishing pole with an improvised hook on the end to hook the string.

You will know when you have hooked the string and you. How to pull wire into an existing wall? Keep lowering the fish tape until the nail connects to the magnet stuck on the wire. Head back to the opening where the wire was sitting and remove the magnet and the nail, then tie the fish tape to the wire. All that’s left is to retract the fish tape to thread your wire through!

Learn how with this video. For more in depth informatino about running fish wire and cable through walls please. If you have access to where the flex bit pops out, attach your wire directly to the bit and fish the wire through that way.

Watch as joe shows you how he fishes a wire down a wall. Running electrical wires allows you to add additional outlets or switches where needed. Mud rings are approved only for low-voltage wires like communication and coaxial cables. If you need to install a regular gang box for an electrical receptacle or wall switch , install the mud ring temporarily to protect the drywall while you fish the wire , then remove it. Use a fiberglass rod with a bull-nose end.

If you’re fishing a small cable (like a security cable), you can attach the cable to the end of the rod by threading one of the wires in the cable through the hole in the bull-nose. If you need to fish a larger cable or bundle (or if your buddy is going to feed the cable to you from above or below), thread a pull-cord through the bull-nose. If both walls are insulate run the wire between the two bottom plates. If only the scone wall , run the wire from the bottom plate all the way to the switch location. Either send a fish between the holes in an insulated wall , or attach a weight to fishing line and send it down from the top hole.

Get Wires Fish ing With Fast and Free Shipping on eBay. Bay Is Here For You with Money Back Guarantee and Easy Return. Get Your Wires Fish ing Today! Once your hole is drille you can shove a glow rod through the hole, attach your wire to the eyelet at the end and pull it back through. Glow rods can also be used to hook wires to pull them out.

If you want to fish electric wire through a wall , the goal is to hit the space between the studs and avoid any potential conflicts with obstacles within the stud cavity. Plumbing pipes, wood blocking and horizontal electrical conduit (feeding a nearby wall switch, for example) can make fishing a new conduit difficult or impossible. Horizontal electrical feeds are much more common in residential work.

Commercial electrical rough-in is usually fed vertically down the walls from the ceiling plenum. The idea is to drop this magnet behind the wall , and use a second magnet to fish it through to where the cable needs to go. Whether sticking the magnet into the wall from above in the attic, or from below in the basement, the idea is the same.

Tape the wire you want to fish up the wall to the end of one of the rods. Work it around a bit, moving toward the side of the wall that the fixture goes on. Fishing Wire Through Walls. After years in construction, Dan Groot had grown tired of crawling up into attics to pinpoint the exact spot to drill a hole for fishing wire down through the walls. During sweltering Florida summers, temperatures in these spaces can climb to well over 130F.

Use the utility knife to slice open the outer insulation jacket on the electrical wire cable (about inches long). Separate the wires within by bending two of them back and leaving one still standing. Grab the wire as it emerges from the hole. There are a variety of methods of fishing wires through walls.

The most crude being brute force with some cable types. Coax can often easily be pushed down walls. Then drop a string down from the top, tie it to the end of the wire and pull it back up. Attach the wire or cable to a fish tape or coat hanger using electrical tape, and feed it into the hole until it reaches the opening at the other end.

If you’re working from the attic, you can drop a weighted string down wall cavity, then attach the wire to the string and pull it through. Run the wire or cable to its destination.