Ductwork in attic

How to insulate ductwork? Add more insulation. Dana Dorsett would have Ted get the level of insulation much closer to the R-recommended in the. GBA senior editor Martin Holladay notes that the. When HVAC ducts are installed in a vented attic in a dry climate, bury the ducts in attic insulation to protect them from temperature extremes in the unconditioned attic space.

Attics are almost as cold as the outdoors during the winter, and can be much hotter than the outdoors during the summer. Insufficient attic insulation, poor air sealing, and uninsulated ductwork are all common problems that will lead to uncomfortable rooms and make your home less efficient. Air sealing your attic and ducts , installing blown cellulose insulation, and insulating ductwork will eliminate these problems. With hundreds of square feet of ductwork surface area in the attic and a ΔT of 75° F, the air coming out of the vents in your home will be significantly higher than 55° F. Throw duct leakage into the mix, and the problems are even worse.

Yes, when you bury ducts in attic insulation in a humid climate, you increase the risk of water vapor condensation on the jacket of the duct insulation. The answer is simple. But in my last article, I also showed you some preliminary from a research study on buried ducts in a hot humid climate.

Ductwork located in an attic crawl space may be difficult to get to and creates a hot and potentially hazardous environment for the crew. Installing ductwork in the crawl space beneath a home limits movement and poses a lighting challenge. Think about it, condensation on ductwork probably isn’t a big problem in Phoenix, Arizona, but why?

However, an attic in Pensacola, Florida is likely to have a humidity level closer to 1 and the risk of condensation on ductwork would then go up quite a bit. From furnace installed anywhere in a house or in attic. From air handler installed in a house or in attic. There are several reasons for running ductwork in attic : House is very big and spacious and there are not enough walls for all heat runs and cold air returns.

Ductwork running along an open ceiling in the basement of a one-story home is also more affordable to replace. Contractors will plan the lines of ductwork needed according to your lighting, then cut the ducting to fit the planned lengths. Ductwork installation will almost always take place in your attic.

Joints are attache and the ducting is connected to vents and your HVAC system. Expect to pay $35-$per linear foot (including labor and materials). Visually inspect the ductwork in areas where it is expose such as attics and crawl spaces. Examine the joints between spans of ductwork for deteriorating duct tape used as sealant during original. When ducts are located outside the conditioned space, they should be sealed to prevent loss of conditioned air and also insulated to prevent thermal loss or gain from the ambient air.

When the location of HVAC equipment and duct system and not optimized in the planning phase, the equipment may end up far away from the space to be cooled. That may require long runs of ductwork that make it hard for your HVAC system to move conditioned air to certain areas within the space. Once the moisture condenses from the air, your attic 's ventilation system can no longer efficiently remove it, and mold can become a significant concern.

Foam insulation board is. Attic Systems provides complete ductwork services for all your ductwork problems, helping make your home more comfortable and energy efficient. Insulation is rated in terms of its thermal resistance. It gets an assigned R-value,.

Get a Free Estimate! Sealing Before You Insulate. Before you insulate the ducts, you need to seal the ducts. Ducts are inherently leaky at. Choosing the Type of Duct.

Hold the loose end of a roll of duct support webbing against the side of a roof joist sitting directly above the flex. Secure the webbing to the joist by hammering a 2-inch roofing nail through the webbing and into the side of the joist. Most contractors would never consider installing uninsulated ducts in a vented attic or crawlspace but regularly do in basements and foamed attics. If the ducts are going to be conceale all seams need to be taped or caulked. Here’s Bob’s trick for taping a seam on a pipe that’s installed close to the subfloor: Cut a piece of foil tape to length.

Peel off part of the backing. Slide the backing up and over the pipe. If they are located in your attic , be sure the area is properly insulated and any cracks or holes are sealed. If you live in a consistently humid climate, a dehumidifier can help keep the air around your ductwork dry. Unblock any ducts that are restricting air flow and have them cleaned regularly.

Use Your Color, Pattern and Even Your Logo.